Roller Shutter
installation guide

Installing roller shutters has been made effortless

We would like to offer you a clear and concise set of instructions for installing your unique roller shutters. Your customized kit is designed to be extremely simple to use, so take pleasure in the experience of effortlessly clicking, sliding, and locking the parts together.

Tools you’ll need to install

  • Drill 
  • Hammer 
  • 10mm drill bit 
  • 05mm drill bit 
  • 05 or 06mm masonry drill bit.
    (Depending on the wall plug size chosen) a
    nd screws to suit. For timber framed windows, just screws. 

Step 1

Mark the top horizontal position of the roller shutters on the wall above the window. On this line mark the width of the shutter. From these two marks, vertically level down each side of the window. You will now have the outline of the roller shutter marked on the wall. At this stage, you can check that the roller shutter is central to the window and is exactly horizontal and vertical. THIS IS MOST IMPORTANT! 

HARD-WIRED ELECTRIC MOTORS ONLY

With the outline of the roller shutter now marked on the wall, you can now decide the best point of entry for the main power and pre-drill the hole before installing. 

IN REVEAL

Basically the same principle, but your window is your horizontal and vertical position. Still, check that they are exactly horizontal and vertical. THIS IS MOST IMPORTANT! 

Step 2

Measure the depth of the head box, then from the top horizontal position of the roller shutter which  you have marked on the wall, measure this distance down each side. This will then give you the  position of the top of the guide on each side of the window. For in reveal roller shutters you can now  cut the guide to the exact length, and angle of the sill.

Step 3

Hold the guide in the two positions marked. Top of the guide position (as in step 2) and the vertical guide position (as in step 1). You can now mark the best position to fix the guide to the wall, and these marks can be transferred to the other side guide. You can now drill through the front and back of the guide, the drill size is determined by the size of the screw you use. The front of the guide will need a  10mm hole, in which the 10mm coloured hole plugs are inserted, this then covers up the fixing points.

IN REVEAL

The fixing holes are drilled from the curtain side 10mm to the outside 05mm.
You will need a 10mm coloured plug.

On Wall Mounting

In Reveal Mounting

ODS BATTERY OPERATED ONLY

From the inside of the house find the desired position of the controller, then transfer the position to the outside wall behind the guide. Then drill through the wall.  This hole is for the cable to the wall plate as shown below.

Step 4

The headbox has pre-drilled holes to attach the head box cover after installation. The guide legs can now be slid into position, (die-cast legs that fit onto the bottom corner of each side of the head box, and connect the main assembly to the roller shutter guides, remove the rubber rings first).  Then slide the roller shutter guides on each side leg. Carefully place the roller shutter on the outline of the roller shutter marked on the wall and mark your fixing points. Then drill and plug the wall if masonry; if it is a timber wall, just a pilot hole to suit the fixing screws.

ODS BATTERY OPERATED ONLY

On the back of the guide drill a 10mm hole to allow the motor  cable to exit the guide and enter the home.

Step 5

Carefully place the roller shutter next to the window. Then;

HARD-WIRED ELECTRIC MOTORS ONLY

Feed the cable from the motor through the hole you have  pre drilled in step 1, this will help the electrician.

ODS BATTERY OPERATED ONLY

Insert a piece of wire through the cable hole in the wall, then attach the cable from the roller shutter to the wire and start pulling the cable into the house. Raise the roller shutter to the outline of the roller shutter marked on the wall and then screw the roller shutter to the wall.

ON WALL INSTALLATION

Then insert the 10mm coloured guide plugs.

Please note: The curtain will not move until the motor has power to turn the axle. If the shutter height limit is not set correctly, the bottom bar of the curtain has a  bottom bar V stopper on each side, which stops the curtain from going completely into the head box, but this causes the motor to jam and stop, this should be avoided and the up limit set to stop the curtain before this happens. 

ODS BATTERY OPERATED ONLY

The cable can now be clipped to the wall plate, and fixed to the wall. When the controller is fully  charged, place it in the wall plate and check the operation of the curtain. If the curtain runs in the  opposite direction to the indicated arrow, swap the wires around on the wall plate. 

Your roller shutter is supplied with either an L10 or a T20 battery motor, depending on its size. Roller shutters under 600mm wide are fitted with the L10 battery motor. This motor is pre-set at the factory and will automatically stop at the fully open and fully closed positions.

Larger roller shutters are fitted with the T20 battery motor. Its limits are not set at the factory, so a tool is supplied with each motor for you to set the up and down end limits yourself.

Important: check which motor you have before you operate your shutter. Motor models can vary between orders, so do not assume your shutter's limits are already set. If you have a T20, set the up and down limits first, following the steps below. Running the shutter before the limits are set can jam the motor and damage the curtain and slats. If you are not sure which motor you have received, email us at [email protected] before operating the shutter.

When adjusting the limits setting screw the plus (+) will add travel and the minus (-) will reduce travel.

Setting up and down end limits

To set the down and top stop limits of your roller shutters, you may need to rotate the limit screw on the motor head up to 30 times. It's recommended to have two people during this process - one person stationed near the stop button on the controller inside the house, and the other person adjusting the down stop limit screw until the curtain stops in the correct position.

To ensure that the top stop limit is properly set, stop the curtain two slats down from the bottom of the head box using the limit screw adjustment, and then adjust the curtain height again by using the limit screw adjustment to stop the curtain 3 cm from the bottom of the head box.

It's important to set the height correctly to avoid the motor jamming and stopping due to the bottom bar V stopper on each side of the curtain, which prevents it from going completely into the head box. Instead, the up limit should be set to stop the curtain before this happens.

When the curtain is in the down position you will be able to fix the head box to the wall, this should be done on each side through the head box end plate. Then rivet the head box cover on and you are done.

Well done, you did it

What do you think about sharing a photo of your project and tagging us?

Thanks for choosing Shutters4U.

If you still have any questions, please give us a call or send us a message

Frequently Asked Questions

Roller Shutters

What are roller shutters?

Roller shutters are a type of window or door covering that consists of horizontal slats or panels hinged together. These slats are typically made of aluminium or steel, although other materials like PVC or wood may also be used. The shutters are mounted above the window or door opening and can be manually or motor-operated.

What are the advantages of roller shutters?

Overall, roller shutters offer a range of advantages for your home, including enhanced security, privacy, light and noise control, energy efficiency, weather protection, and ease of maintenance. They can be a valuable addition to any property, providing numerous benefits to you and your loved ones.

Can roller shutters make a room completely dark?

Roller shutters can significantly reduce the amount of light entering a room. Keep in mind that the darkness level will depend on various factors like the material and design of the shutters, the installation method, and if there are any gaps or light leaks around the edges.

Are roller shutters secure?

Nowadays roller shutters are considered one of the most secure options for windows and door coverings. That’s because of the extra layer of protection that makes it more difficult for intruders to gain access to your home or commercial property.

However, to keep your home safe with roller shutters, we always suggest ensuring proper installation, regular maintenance, and use of other security measures in combination with security roller shutters, such as alarms, motion sensors, and reinforced entry points, to enhance the overall security of your property.

Do roller shutters provide insulation for your home?

Yes, roller shutters can provide insulation for your home and contribute to energy efficiency as they act as an additional insulating layer on windows and doors. In fact, in colder seasons, roller shutters can help retain heat inside the house, while in hot weather, they can block out heat from entering.

By investing in high-quality roller shutters from shutters4u, you can boost their insulation properties and enjoy the benefits of improved energy efficiency and indoor comfort.

How to clean roller shutters at home?

Cleaning roller shutters at home is an easy process. All you need to do is to wash them with soft soap and scrub them with a sponge or microfibre cloth. Before that, ensure the shutters are closed to clean their interior and exterior. Also, first, remove any debris or dust from their surface.

Remember, regular cleaning and maintenance of roller shutters will help keep them in good condition and prolong their lifespan.

Where can be roller shutters installed?

The versatility and customizable nature of roller shutters make them suitable for various applications, and they can be tailored to fit your specific needs and requirements. Just to mention some examples, roller shutters are usually installed in windows, doors, shopfronts, warehouses, industrial buildings and more.

What roller shutter colours are available in shutters4u?

We have a brilliant colour palette available for shutters in Australia, starting from the classics to the ones that deck up pretty well with your space. Our team also offers customization in terms of colours and brings different combinations for your home or business space. You name it, and we provide it. 

If you need ideas for what colours will match your home then give us a call, and we will be happy to suggest the best colour options for you.

How to install DIY roller shutters?

Installation instructions for your DIY roller shutters are available in a detailed step-by-step video as soon as your order is placed. In your order, you will receive a link to a set of videos with instructions on how to install your shutters.

We have a separate video for motorised and manual roller shutter installation, so no matter what you choose you have everything you need to be able to install the shutters yourself with no issues.

Still not sure if DIY Roller Shutters are for you?

We got you covered. If you'd rather have yours installed, get in touch and we'll point you in the right direction.

Have any questions?
We're here to help

Contact Us

"*" indicates required fields

This field is for validation purposes and should be left unchanged.
Name*
Please let us know what's on your mind. Have a question for us? Ask away.